Imbus/grbl-imbus
1
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions

v1.1f. Parking override control. Spindle enable pin option.

Browse source 
[ver] v1.1f update due to tweaks to interface from new parking override
control.

[new] Parking motion override control via new `M56 P0` and `M56 P1`
command, which disables and enables the parking motion, respectively.
Requires ENABLE_PARKING_OVERRIDE_CONTROL and PARKING_ENABLE enabled in
config.h. Primarily for OEMs.

[new] `M56` appears in the $G report when enabled.

[new] Five new build info identification letters. Some were missing and
a couple are new. Updated the CSV and documentation to reflect these
new items.

[new] Spindle enable pin configuration option to alter its behavior
based on how certain lasers work. By default, Grbl treats the enable
pin separately and leaves it on when S is 0. The new option turns the
enable pin on and off with S>0 and S=0. This only is in effect when a
user enables the USE_SPINDLE_DIR_AS_ENABLE_PIN option.

[fix] M4 is now allowed to work when USE_SPINDLE_DIR_AS_ENABLE_PIN is
enabled. Previously this was blocked and was problematic for laser
folks using M4.

[fix] Properly declared system variables as extern. Not sure how that
went unnoticed or why it worked up until now but it has.

[fix] EXTREMELY RARE. When AMASS is intentionally disabled and sent a
motion command that is _one step_ in length, Grbl would not actuate the
step due to numerical round-off. Applied a fix to prevent the round-off
issue.

[fix] Added a compile-time check for AMASS settings to make sure that
the numerical round-off issue doesn’t effect it. This would only happen
if someone set AMASS max levels to zero. It does not effect AMASS with
its current defaults.

[fix] Wrapped the mc_parking_motion() function in an ifdef for porting
purposes.

[fix] Fixed an issue when in inverse time mode and G0’s would require a
F word. This was not correct.

[fix] Added a note in the defaults.h file that MAX_TRAVEL values must
be positive. Some users were setting this negative and it was causing
issues.
This commit is contained in:
chamnit 2017-01-28 17:13:06 -07:00
parent 67ab9280d9
commit e455764079
19 changed files with 259 additions and 102 deletions
Download patch file Download diff file Expand all files Collapse all files

51
grbl/motion_control.c
View file

@ -313,29 +313,42 @@ uint8_t mc_probe_cycle(float *target, plan_line_data_t *pl_data, uint8_t parser_
// Plans and executes the single special motion case for parking. Independent of main planner buffer.
// NOTE: Uses the always free planner ring buffer head to store motion parameters for execution.
void mc_parking_motion(float *parking_target, plan_line_data_t *pl_data)
{
if (sys.abort) { return; } // Block during abort.
#ifdef PARKING_ENABLE
void mc_parking_motion(float *parking_target, plan_line_data_t *pl_data)
{
if (sys.abort) { return; } // Block during abort.
uint8_t plan_status = plan_buffer_line(parking_target, pl_data);
uint8_t plan_status = plan_buffer_line(parking_target, pl_data);
if (plan_status) {
bit_true(sys.step_control, STEP_CONTROL_EXECUTE_SYS_MOTION);
bit_false(sys.step_control, STEP_CONTROL_END_MOTION); // Allow parking motion to execute, if feed hold is active.
st_parking_setup_buffer(); // Setup step segment buffer for special parking motion case
st_prep_buffer();
st_wake_up();
do {
protocol_exec_rt_system();
if (sys.abort) { return; }
} while (sys.step_control & STEP_CONTROL_EXECUTE_SYS_MOTION);
st_parking_restore_buffer(); // Restore step segment buffer to normal run state.
} else {
bit_false(sys.step_control, STEP_CONTROL_EXECUTE_SYS_MOTION);
protocol_exec_rt_system();
}
if (plan_status) {
bit_true(sys.step_control, STEP_CONTROL_EXECUTE_SYS_MOTION);
bit_false(sys.step_control, STEP_CONTROL_END_MOTION); // Allow parking motion to execute, if feed hold is active.
st_parking_setup_buffer(); // Setup step segment buffer for special parking motion case
st_prep_buffer();
st_wake_up();
do {
protocol_exec_rt_system();
if (sys.abort) { return; }
} while (sys.step_control & STEP_CONTROL_EXECUTE_SYS_MOTION);
st_parking_restore_buffer(); // Restore step segment buffer to normal run state.
} else {
bit_false(sys.step_control, STEP_CONTROL_EXECUTE_SYS_MOTION);
protocol_exec_rt_system();
}
#endif
}
#ifdef ENABLE_PARKING_OVERRIDE_CONTROL
void mc_override_ctrl_update(uint8_t override_state)
{
// Finish all queued commands before altering override control state
protocol_buffer_synchronize();
if (sys.abort) { return; }
sys.override_ctrl = override_state;
}
#endif
// Method to ready the system to reset by setting the realtime reset command and killing any