c0f61e4aac
- Reverted back the serial RX count function to how it was. The variable type was unsigned and cause an integer underflow whenever the calculation produced a negative number. The old way was the correct way. - Lots of minor edits to the code CSVs and markdown documents. - Expanded on explaining feedback messages and startup line execution feedback. - Created a new settings codes CSV to help GUIs import the values and meanings.
35 lines
2.8 KiB
CSV
35 lines
2.8 KiB
CSV
(KEY: Error Code in v1.1+ ,Error Message in v1.0-, Error Description)
|
|
1,Expected command letter,G-code words consist of a letter and a value. Letter was not found.
|
|
2,Bad number format,Missing the expected G-code word value or numeric value format is not valid.
|
|
3,Invalid statement,Grbl '$' system command was not recognized or supported.
|
|
4,Value < 0,Negative value received for an expected positive value.
|
|
5,Setting disabled,Homing cycle failure. Homing is not enabled via settings.
|
|
6,Value < 3 usec,Minimum step pulse time must be greater than 3usec.
|
|
7,EEPROM read fail. Using defaults,An EEPROM read failed. Auto-restoring affected EEPROM to default values.
|
|
8,Not idle,Grbl '$' command cannot be used unless Grbl is IDLE. Ensures smooth operation during a job.
|
|
9,G-code lock,G-code commands are locked out during alarm or jog state.
|
|
10,Homing not enabled,Soft limits cannot be enabled without homing also enabled.
|
|
11,Line overflow,Max characters per line exceeded. Received command line was not executed.
|
|
12,Step rate > 30kHz,Grbl '$' setting value cause the step rate to exceed the maximum supported.
|
|
13,Check Door,Safety door detected as opened and door state initiated.
|
|
14,Line length exceeded,Build info or startup line exceeded EEPROM line length limit. Line not stored.
|
|
15,Travel exceeded,Jog target exceeds machine travel. Jog command has been ignored.
|
|
16,Invalid jog command,Jog command has no '=' or contains prohibited g-code.
|
|
20,Unsupported command,Unsupported or invalid g-code command found in block.
|
|
21,Modal group violation,More than one g-code command from same modal group found in block.
|
|
22,Undefined feed rate,Feed rate has not yet been set or is undefined.
|
|
23,Invalid gcode ID:23,G-code command in block requires an integer value.
|
|
24,Invalid gcode ID:24,More than one g-code command that requires axis words found in block.
|
|
25,Invalid gcode ID:25,Repeated g-code word found in block.
|
|
26,Invalid gcode ID:26,No axis words found in block for g-code command or current modal state which requires them.
|
|
27,Invalid gcode ID:27,Line number value is invalid.
|
|
28,Invalid gcode ID:28,G-code command is missing a required value word.
|
|
29,Invalid gcode ID:29,G59.x work coordinate systems are not supported.
|
|
30,Invalid gcode ID:30,G53 only allowed with G0 and G1 motion modes.
|
|
31,Invalid gcode ID:31,Axis words found in block when no command or current modal state uses them.
|
|
32,Invalid gcode ID:32,G2 and G3 arcs require at least one in-plane axis word.
|
|
33,Invalid gcode ID:33,Motion command target is invalid.
|
|
34,Invalid gcode ID:34,Arc radius value is invalid.
|
|
35,Invalid gcode ID:35,G2 and G3 arcs require at least one in-plane offset word.
|
|
36,Invalid gcode ID:36,Unused value words found in block.
|
|
37,Invalid gcode ID:37,G43.1 dynamic tool length offset is not assigned to configured tool length axis.
|